ElevateDrawings.com

Using ElevationBuilder

Everything the app draws, and the rules it follows.

Before anything else. ElevationBuilder produces representative elevations for coordination, submittals, estimating and pricing. They are not manufacturing drawings. Dimensions are nominal, and every sheet says so above the title block. Verify in the field before anything is fabricated.

1The screen

The window is in two halves. On the left is the sidebar, where you build the drawing. On the right is the canvas, which shows the printed sheet exactly as it will come out.

Four tabs at the top of the sidebar — Doors, Frames, Jambs and Storefront — are the four pages of the drawing set. Each holds its own elevations and prints as its own sheet or sheets. Below the tabs, a dropdown and + Add button add an elevation to the page you are on.

Every elevation you add becomes a card. Click a card's header to open or collapse it. Adding a new elevation collapses the others so the one you are working on is the one you can see. The × on a card removes that elevation.

The canvas redraws as you type. There is no preview button and nothing to refresh.

2How dimensions work

You type decimals. The drawing prints fractions. Entering 5.875 is quicker than hunting for a fraction, so the input fields take decimals — but the sheet reads 5-7/8", the way a schedule reads. Fractions resolve to the nearest 1/32" and reduce properly, so you get 7/8" rather than 28/32".

This is a display convention. The geometry still uses the exact decimal you entered; only the printed text is rounded.

Marking a dimension VAR.

Every dimension field has a small set button beside it. Click it and that dimension switches to VARIES: the field greys out, the button turns amber and reads VAR, and the drawing prints VAR. in place of a number.

Use it when one elevation covers a run of openings at different sizes, or when a dimension has not been confirmed yet. The drawing still has to be drawn at some size, so the app uses a sensible stand-in for the geometry and prints VAR. over it. Click the button again to go back to a fixed number.

Nominal sizes

Dimensions are nominal throughout. A pair of 36" leaves is drawn and dimensioned as 72" overall — the undercut and the meeting-stile clearance that a manufacturer deducts are not shown, because these are not manufacturing drawings.

3Door elevations

Page 1 draws door leaves: eight types, in flush, narrow vision, half glass and full glass, each as a single or a pair. The type you choose sets the starting lite; everything after that is yours to change, and any door can carry any combination of lites and louvers.

Widths

A single door has one Width. A pair has Left leaf width and Right leaf width, entered separately, and the overall is their sum.

Unequal pairs need no flip control. Entering 42" and 18" draws the wide leaf on the left; entering 18" and 42" draws it on the right. Swapping the two numbers is the mirror, so there is nothing else to set.

The drawing dimensions each leaf on the inner line and the overall below it.

Hinges

Hinges are drawn automatically from the door height, following the usual rule:

Door heightHinges
Up to 60"2
Over 60" to 90"3
Over 90" to 120"4

Two for the first 60", then one more for every additional 30" or part of it. The top and bottom hinges sit with their centrelines 9" from each end of the door, and any intermediate hinges divide the span between them equally. The symbol is drawn as a 4-1/2" hinge.

On a pair, both leaves get hinges on their outer stiles. That is true in all four handings, so pair hinges are drawn without you choosing a hand.

Show hinges on each card turns them off for that elevation. It changes nothing else — the piece keeps its size, dimensions and hardware.

Levers

A lockset is hand-specific in a way hinges are not, so the lever is opt in. A single door has Show lever / lockset; a pair has Lever on left leaf and Lever on right leaf.

Leave both off and one elevation serves right-hand active, left-hand active and both reverse variations without being wrong for any of them. Turn one on when the drawing needs to show which leaf is active.

The lever is drawn at a 2-3/4" backset, 40" above the finished floor, pointing away from the centre of a pair so it clears the astragal. That height is a drawing convention and is not dimensioned.

Astragal

Astragal at meeting stiles on a pair draws a 2" astragal centred on the meeting line. Unchecked, the meeting line is drawn as a plain line. It is a single on-or-off choice — these are representative drawings, so the astragal is not specified by type or handed to a leaf.

Vision lites

+ Add lite adds a lite to the card. Each lite has its own width, height, distance from the top edge, and either a distance from the lock stile or centring in the leaf.

Auto width

Half glass and full glass lites size themselves to the leaf: leaf width less 12", which leaves a 6" stile each side. On a 36" leaf that is a 24" lite; on a 42" leaf, 30". Uncheck Auto width to enter a width by hand.

A width you enter by hand is honoured as entered, but capped at the leaf width — narrower stiles than the 6" allowance are a legitimate choice, glass wider than the door is not.

When a lite is left out

A leaf that cannot hold a 6" lite inside the 12" stile allowance shows no lite at all. That works out to any leaf under 18", and it applies whether the width is automatic or entered by hand.

This is what makes unequal pairs behave. A 42" + 12" pair with one half-glass lite draws a 30" lite in the wide leaf and nothing in the narrow one, which is what such an opening actually looks like.

Vertical position

A lite never comes within 5" of the top or bottom rail. If you set it closer, the distance from the top is held at 5"; if the height would push the bottom edge past the limit, the height is trimmed. Under 6" of remaining glass, nothing is drawn.

The drawing always reports the size it actually drew, so a dimension on the sheet can never disagree with the picture.

Which leaf it appears on

On a pair, each lite has Appears on with a checkbox for the left and right leaf. Both are on by default. Clear one and the lite is drawn only in the other leaf — for an unequal pair with glass in the active leaf only, clear the inactive side.

Louvers

+ Add louver works the same way, measured from the bottom of the door instead of the top. Louvers are always centred in the leaf, size themselves to the leaf less 12" unless you turn Auto width off, follow the same suppression and 5" clearance rules, and carry the same Appears on choice. Metal and wood are drawn with different hatching.

4Frame elevations

Page 2 draws hollow metal frames: single, pair, with sidelite, and borrowed lite. All of them show a 2" face with mitered corners at the head.

Wall type and jamb depth

Jamb depth is the front-to-back depth of the frame, out of the wall. It is not a width. The defaults follow the wall type:

Wall typeJamb depthThroat
Masonry5-3/4"4-3/4"
Drywall5-7/8"4-7/8"

The throat is the clear dimension between the two returns, and it is the jamb depth less the two 1/2" returns.

Switching the wall type moves the depth to that wall's default — but only while the depth is still sitting on one of the two defaults. Once you have typed a depth of your own, changing the wall type leaves your number alone.

Openings

A single or sidelite frame has one Clear width. A pair frame has Left opening and Right opening, entered separately, with the running overall shown beneath them on the card.

Centre mullion

Include centre mullion on a pair frame draws a 2" mullion between the two openings.

The mullion adds to the opening. It is a member of the frame, not something carved out of the clear width. Two 36" openings with a mullion give a 74" overall, not 72". Checking the box therefore widens the frame.

There is no offset setting. Unequal openings put the mullion where it belongs on their own — enter 42" and 18" and the mullion sits 42" from the left jamb.

Head size

Masonry frames offer 4" head (masonry coursing), for when the opening height plus a standard 2" head does not land on the nearest 8" course. The extra 2" is added above the head; the opening below it does not move.

Sidelites

A sidelite frame adds Sidelite width and two more choices:

  • Sidelite — glazed, or a solid panel.
  • Sidelite sill height — none, 2", 4" or 6". Choose None and the glazing or panel runs to the floor.

Transoms

Include transom adds a fixed panel above the door opening in the same frame, with its own height and a glazed or solid panel choice. A 2" transom bar separates it from the opening below, and the transom spans the full inner width including a sidelite. A centre mullion stops at the underside of the transom bar rather than running up through it.

Borrowed lites

A borrowed lite is a four-sided frame with mitered corners and glazing throughout — an interior window rather than a door opening. It takes a clear width and height and a wall type, and defaults to 36" × 36".

5Jamb and head profiles

Page 3 draws cross-sections through the frame. Eight profiles, each in a masonry and a drywall version:

ProfileWhat it is
Double rabbetThe standard frame, rabbeted on both sides of the stop.
Single rabbetRabbeted on one side, with the soffit growing as the jamb depth grows.
Cased openingNo stop and no rabbet — a lined opening with no door.
Double egressStepped, for a pair swinging in opposite directions.

Each section is dimensioned out to out across the jamb depth, with the face sizes dimensioned on the legs. The caption under each reads the jamb depth, the derived throat and the face size.

Face size

Masonry profiles offer a 2" or 4" face. The 4" face is measured from where the door sits in the frame, so on a double egress a 1-3/8" face becomes 3-3/8" and a 2-5/8" face becomes 4-5/8". Drywall profiles are fixed at a 2" face.

Welded head

Double egress profiles carry a Welded head (single step) checkbox. Unchecked, the section is the stepped profile used for the jamb and a knock-down head. Checked, it draws the single-step head used when the frame is welded. The caption notes which one is drawn.

When the jamb depth changes, the step the door sits against stays put and the sections either side of it adjust.

6Storefront elevations

Page 4 draws storefront and curtain-wall style openings: a framed door with an optional transom, and glazed bays beside it. A storefront can also be bays only, with no door. Members are drawn in a light grey and the glass is hatched like every other lite in the app.

The card starts with the overall size: Member face (1-3/4" or 2"), Overall width and Overall height, plus the Door opening height and the Bottom member. Transom over door adds the fixed lites above the door.

The door

Door is single, pair or none. A single door has one Leaf width; a pair has Left leaf and Right leaf. Hinges (from outside) sets the hand, and Stile / top rail (narrow 2-1/8", medium 3-1/2" or wide 5") and Bottom rail size the door. Swapping the hinge side mirrors the door, and its pull reverses with it.

Side bays

Bays on puts glazed bays on the left, the right or both sides of the door, or none. Each side has a # of bays and a bay width, or a list of custom widths such as 30, 42, 36. Width entry can instead be Overall + max glass: give the overall width and the widest glass you will allow, and the bays divide themselves equally. The card shows the width the frame actually builds to; if it differs from the overall you typed, a warning says by how much.

Bottom of glass sets how far above the floor the glass starts on a side. Leave it at 0 for full-height glass, or raise it for half-height bays. The height has to clear the bottom member and leave room for glass, or the app draws full-height glass and says so in a warning. (Pro) The free version draws full-height bays.

Lites and mullions

Each bay can be divided horizontally. Choose Bay lites high by a count or a maximum height, or type exact split heights measured from the floor. Split heights measure to the centreline of the member or the top of the lite beneath it.

By default the side-bay horizontals align with the door transom bar. Choose Independent of door to give the side bays their own lite divisions, with Lower bay lites below the bar. (Pro)

The transom has its own controls: Transom lites by count or maximum height, custom split heights, and Mullions over door by maximum bay width or a bay count, or custom widths. The last transom bay adjusts so the bays fill the door width exactly.

Pull handle

Doors are drawn with a 12" offset pull, mounted on the lock stile with the grip standing off toward the middle of the leaf. It reverses when you change the hinge side. Show pull handle turns it off; on a pair, Pull on left leaf and Pull on right leaf are separate.

Warnings

When the layout cannot be drawn exactly as entered — widths that do not add up to the overall, split heights that do not fit, too many divisions for the height — the app draws it as close as it can and shows a red note above the elevation and on its card. The note is for you on screen only; it never prints or exports.

7Sheets and the title block

Each page lays itself out on an 11" × 8½" sheet in landscape. Elevations fill left to right and wrap to a new row; when a row will not fit, the page starts another sheet and the sheet count in the title block follows. Content is centred vertically on the sheet.

The Project details button at the top of the sidebar opens a dialog with the project name, revision and Drawn by, which feed the title block, along with the drawing scale for the tab you are on and the sheet notes. The project name and revision are shown next to the button, and in Pro a second line shows the file name a saved project will get (for example hillcrest_high_school_rev_b.json). Your name or firm is remembered between visits, so you enter it once.

Each elevation card has an Elevation label field for its mark — EL-1, F-3, and so on. Enter one and it prints in bold beneath the elevation with the type and material under it; leave it empty and the type prints on its own.

Each card in Pro also has Qty (openings) and Opening marks, used by the glass report. Put the door tag numbers an elevation applies to in Opening marks (for example 101, 104, 106) and its Qty is the count of them. You can also just type a Qty with no marks. If you fill in both and they disagree, a red warning appears on the card. Neither prints on the drawing.

Above the title block, every sheet carries the note: All dimensions nominal inches unless noted. Verify in field before fabrication.

8Saving and recovery

Save writes your project as a .json file to a location you choose on your own computer. Load opens one back up. New clears the board and starts over.

Your projects are files on your disk, not records on a server. Nothing you draw is ever sent anywhere. That also means a lost file cannot be recovered from us — keep backups as you would for any document.

In Chrome and Edge, Save and Load use the browser's own file picker, and the dialog opens where you last saved so a set of project folders stays easy to work with. Firefox and Safari do not offer the picker yet; there, Save downloads the file to your downloads folder and Load asks you to choose one.

If the tab closes

The app keeps an autosave copy of the current drawing in your browser as you work. Reopen the app after an accidental close or a crash and it offers to restore it. This is a safety net between saves, not a filing system — it holds one drawing, it lives only in that browser, and clearing your browser data clears it. Save properly to a file for anything you need to keep.

9Printing and export

Print opens the sheets of the tab you are on in a print view sized for 11" × 8½" landscape. Set your printer to landscape and turn off any "fit to page" scaling. Printing to PDF from the same dialog gives you a PDF of that tab's sheets. Doors, Frames, Jambs and Storefront each print on their own, so for the whole set, print each tab in turn.

Export opens a menu with two choices, and like Print it works on the tab you are on. SVG writes the sheets as SVG files, which open in Illustrator and Inkscape as editable linework rather than a picture. DXF writes them for CAD (AutoCAD, BricsCAD, LibreCAD, FreeCAD and others), at full size in inches, so a 3'-0" door is 36 units wide and the sheet border is the paper size at the drawing scale. Door, frame and profile linework, dimensions and text arrive on separate layers; the drawings come in as outlines without fills. There is one file for each sheet of that tab.

Dark switches the canvas to a dark background with white linework, for working at night. It changes the screen only — printed and exported sheets are always white paper with dark lines, whichever mode you are in.

Glass report

Glass report (Pro) in the toolbar opens a report of the glass in the whole drawing set: door lites, hollow metal frame openings and storefront glass. Solid panels, louvers and door leaves are left out. The report has Print, Export CSV and Close across the top, so you can print or export without closing it.

There are two tables. By elevation lists each elevation's marks, Qty, the glass in one opening (shown size and cut size) and the total pieces: the glass in one opening multiplied by the Qty. Ordering summary rolls matching cut sizes together across every elevation, with where each is used. Print gives a clean white page, and the CSV opens in Excel or Google Sheets with the sizes as fractions and as decimal inches.

Cut sizes

The size on the drawing is not always the size you order. The settings at the top of the report turn the shown size into a cut size, and are saved with the project:

GlassShown on the drawingCut size (default)
Door lites, HM and woodVisible lite sizeShown + the bite on each side. Default bite 1/2", so 1" total.
StorefrontDaylight sizeShown + the bite on each side. Default bite 3/8", so 3/4" total.
HM frame openingsFace dimension of the openingShown less the clearance. Default 3/8" in total (3/16" each side).

For a job that uses wood bead moulding, set the door lite bite to the bead you are using. A door that takes a different kit, such as a fire-rated door with a metal kit, has its own Lite kit bite on its card: Report default, 1/2", 3/8" or Custom. Those lines are marked as an override in the report and the CSV.

Cut sizes are a convenience, not a guarantee. Check them against your glazier's requirements and field measurements before you order.

10Free and Pro

The free version draws exactly what Pro draws. Same engine, same geometry, same sheets — a drawing made in the free version is not marked, watermarked or degraded in any way. What changes is how much you can put on a page and what you can do with the result afterwards.

The real difference is the project file. The free version keeps one drawing, in one browser, through the autosave. Pro saves projects as files you keep — so when a submittal comes back marked up three weeks later, you open the job and change it rather than drawing it again.

What the free version does

  • Three door elevations, three frame elevations, four jamb profiles and two storefront elevations per page
  • Sheet notes, which do not count against those limits
  • Every door and frame type, every jamb profile, all dimensioning
  • Printing, preview, zoom, fullscreen and dark mode
  • Autosave recovery if the tab closes

What Pro adds

  • No limit on elevations per page
  • Save and reopen projects as files on your own disk
  • Export sheets as SVG or DXF for CAD and layout
  • Transoms on frame elevations
  • Half-height storefront bays and independent bay lites
  • The glass report, with print and CSV export
  • Your own name or firm in the DRAWN BY field

Price

Pro is $14 a month per user, or $140 a year per user — the annual plan is two months free, about 56¢ per working day. One licence covers one user, not a whole company or shop. For more than five users, contact us for team pricing.

Everything you have drawn stays exactly as it is if a subscription lapses; you keep your files and the free limits apply again.